If your Safty Data Sheet has not started downloading, or printing, please use the buttons below to try again.

Print this pageDownload PDF

BASF F200 Specs

Revised 2015

Product Data

BASF F-200 is a smooth sphere of activated alumina produced by BASF’s unique manufacturing process. BASF F-200 is an excellent desiccant for drying a wide variety of liquids and gases. Although all molecules are adsorbed to some extent on BASF F-200 activated alumina, those molecules having the highest polarity are preferentially absorbed. Stream conditions such as pressure, concentration and molecular weight of the molecules, temperature and site competing molecules affect the efficiency of adsorption. BASF F-200 is available in nominal sizes of 1/16”, 1/8”, 3/16” and ¼” spheres.

Product benefits

1. Uniform ball size. This property is especially useful in high pressure gas dehydration where minimizing pressure drop is important. The uniform size and sphericity of BASF F-200 prevents adsorbent segregation during pneumatic loading, thus minimizing channeling and yielding more efficient use of the entire desiccant tower.

2. High crush strength. BASF F-200 has high crush strength which allows rapid pneumaticloading of towers. The high crush strength also allows use of taller towers that make more efficient use of the desiccant. BASF F-200 activated alumina is highly resistant to amine attack. Furthermore, BASF F-200’s high crush strength enables it to dehydrate acid containing gases and liquids, such as CO2, for a longer operating life.

3. Low abrasion. The low abrasion of BASF F-200 ensures less dusting during transport, loading, and service life which reduces pressure drop and
minimizes downstream valve and filter plugging, common with dustier products.

4. High adsorptive capacity. BASF F-200’s high surface area and tailored pore distribution provide a high dynamic H2O adsorption capacity. With proper
tower design and effective regeneration, F-200 can achieve an ultra low H2O effluent specification (i.e. dew point). BASF F-200 also has excellent cyclic stability that yields a long life.

Product applications

1. Drying. Nearly all gases and liquids can be dried with F-200. Water removal is often necessary for efficient processing, storage and transportation of fluids. The 3/16” size is normally recommended for vapor phase dehydration applications where pressure drop minimization yet high H2O adsorptive capacity is desired.

The 1/8” and 7 x 14 Tyler mesh sizes are recommended for use in liquid dehydration and other mass transfer limited adsorption applications.

BASF F-200 activated alumina is rapidly becoming the industry standard for drying compressed air. Providing long service life with performance at or below dew point specifications, F-200 is a ‘peace of mind’ product for both large and small dryers. BASF F-200 is appropriate for use in dehydrating
gases in both thermally regenerative (350 to 600°F) and pressure swing (PSA) modes.

2. Acid removal. Transformer oils, lubricating oils, and refrigerants form degradation acids upon use. BASF F-200 will remove these acids during use. In the manufacture of chlorinated and/or fluorinated hydrocarbons, removal of these residual halides and water is essential for a non- corrosive product.

3. Process stream purification. BASF F-200 is excellent for removal of highly polar compounds such as water and alcohol. It also readily adsorbs TBC ad heavy metal ions from hydrocarbons.

4. Hydrocarbon adsorption. Under proper operating conditions, the pore size distributions and surface chemistry of activated aluminas are conducive to the adsorption of hydrocarbons.

Available packaging

  • 50 lb bags
  • 375 lbs steel drums
  • 2000 lb super sacks

About BASF

As the world’s leading chemical company, BASF’s portfolio ranges from chemicals, plastics, performance products, agricultural products and fine chemicals to crude oil and natural gas. BASF’s intelligent system solutions and high-value products help its customers to be more successful. BASF develops new technologies and uses them to open up additional market opportunities. It combines economic success with environmental protection and
social responsibility, thus contributing to a better future.

Chemical composition (wt %)
Al2O3 92.7
SiO2 0.02
Fe2O3 0.02
Na2O 0.30
LOI (250-1100ºC) 7.0
Physical properties 7X14 Tyler Mesh (2.0mm) 1/8” (3.2 mm)  3/16” (4.7mm) m) 1/4” (6.4mm)
Surface area, m2/g 360 350 340 320
Total pore volume, cc/g 0.5 0.5 0.5 0.5
Packed bulk density, lbs/ft3 (kg/m3) 48 (769) 48 (769) 48 (769) 48 (769)
Crush strength, lbs (kg) 11 (5) 30 (14) 55 (25) 70 (32)
Abrasion loss, wt % 0.1 0.1 0.1 0.1

All data represents typical product properties and are based upon BASF standard test methods. All test methods are available upon
request. Information presented herein is believed to be accurate and reliable but does not imply any guarantee or warranty by BASF.

Outline in our Current Safety Data Sheet – Click Here

Although all statements and information in this publication are believed to be accurate and reliable, they are presented gratis and for guidance only, and risks and liability for results obtained by use of the products or application of the suggestions described are assumed by the user. NO WARRANTIES OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE MADE REGARDING PRODUCTS DESCRIBED OR DESIGNS, DATA OR INFORMATION SET FORTH. Statements or suggestions concerning possible use of the products are made without representation or warranty that any such use is free of patent infringement and are not recommendations to infringe any patent. The user should not assume that toxicity data and safety measures are indicated or that other measures may not be required.